/*
{0000/4203}
Graphics initialization error.

cannot select an EGA hi resolution screen.


{0001/3005}
 No line to selected unit.

Check if you have selected the
correct component. Check the
component and connections.

{0002/4004}
The selected component is not available.

Check the component and connections
then use the RETRY command.

{0003/3505}
  Cannot use the GROUP command.

The selected component does not use
the GROUP command. Only components
0 to 3 use this command.

{0004/5006}
        Lost connection to component.

Check the component. You may need to switch it off
and start again or there could be a bad connection
between the Waveterm and the component. Consult
your dealer for further information.

{0005/4405}
           Page Not available.

This page is not available with this version
of software. It may however become available
on future versions.

{0006/4205}
         Sub-page not available.

This sub-page is not available with this
version of software. It may however become
available on future versions.

{0007/6603}
		     Not enough memory.

malloc() failed to reserve the memory required for this operation.

{0008/5605}
		Protected Memory Area.

You have just tried to save or delete a preset waveform.
00 to 09 are preset waveforms. Please try to save to, or
delete a different area.

{0009/4804}
	Waveform Transfer Error.

The component has not responded to the transfer.
Please check the component and cables.


{0010/4801}
Sorry! This page will only run on a VGA monitor.


{0011/6401}
Sorry! The function you have selected hasn't yet been installed.


{0012/4204}
           Restricted Access.

The function you have selected is not
available on the demo version of software.

{0013/7115}
		  Not Installed for MC6821 card.

If using this function with the 6821 based card, a different cable must
be fitted to allow the 2 Waveterms to communicate. Perhaps a short
ribbon cable with an IDC Centronics plug and socket attached?

The new cable is the same as a normal cable except for the following:-

         TERM B          TERM C emulating an EVU.
         ----------------------------------------
         13 CA2                14 CA1
         14 CA1                13 CA2

This function has yet to be programmed into the system. When it has,
you will be able to transfer sounds from a PPG Waveterm-B.

{0014/5703}
		   Number out of range.

The number you have entered is not in the range accepted.


{0015/5204}
		Not a valid mode

You have not entered correctly the mode you require.
Please type STEREO or MONO as required.


{0016/5702}
Sorry! The ~
function hasn't yet been installed in the comms routines.



{0017/6204}
	Page 2.00 doesn't contain any data to transfer.

If any waveforms have been entered on page 2.00, you must
press the page 2.00 COMPUTE button before using this function.


{0018/2101}
No data to work with.


{nnnn/nnnn}
-----------------------------------------------------------------------
		DISK ERRORS
-----------------------------------------------------------------------
{0100/5904}
	    Major disk directory failure.

The system has lost the ability it had to change directory.
This problem can occure if the disk drive has failed.

{0101/5307}
	       Directory not available.

Occures when the directory you have tried to access
has never been created or may be in a different
part of the system. Due to the design of the system,
this error should never occure and if it does, please
contact your dealer.

{0102/5507}
	      Section not available.

Occures when the section you have tried to access has
never been created or may be in a different part of
the system. Due to the design of the system, this error
should never occure and if it does, please contact your
dealer.

{0103/5406}
	   Unable to create directory.

This error will occure if there is already a directory
of the same name or if the disk has failed.
It may also happen if running on a network with low
security rights.

{0104/5206}
	    Unable to create section.

This error will occure if there is already a section
with the same name or the disk has failed.
It may also happen if running on a network with low
security rights.

{0105/5405}
	  Unable to create PPG Directory.

For some reason the system has not been able to create
a file used for keeping track of PPG files. This could
be due to a disk failure.

{0106/5107}
	  Unable to open PPG Directory.

A special file in the system is used to support the
PPG Directory. You will get this error if this file
hasn't been created due to error number 105 or has
been corrupted in some way.
You may also get this error due to a disk failure.

{0107/5004}
       Couldn't find file in PPG Directory.

Check the file number or use the SEARCH command as
it may have been saved in a different section.

{0108/4705}
	     Couldn't open file.

For some reason the PPG Directory has said that
a file exists that dosn't exist or has been
corrupted in some way.

{0109/4505}
	      Directory full.

The current directory you are using is full.
You will have to create another directory for
further storage of files.



{0110/4205}
	     Section full.

The current section you are using is full.
You will have to create another section or
directory for further storage of files.


{0111/3605}
      Unable to delete file.

This file may have been protected.
You may not have the right to delete
this file.



{0112/3003}
Unable to rename ~

The rename section has failed.

{0113/5005}
	    File already exists.

A file already exists with the same name / number
as the one you have chosen to rename your file to.
Please choose a different name / number.


{0114/4104}
	  Not same file type.

You cann't rename a file of one type as a
file of a different type.

{0115/3703}
	  Protected Mode.

No sounds can be stored in this mode.


{0116/3005}
	DOS Write Error.

Unable to open or write to the
Page2.01 temporary disk files.
File: ~

{0117/3005}
	DOS Read Error.

Unable to open or read the
Page2.01 temporary disk files.
File: ~


{0118/2901}
Cann't create FLAGS.DAT file.



{0119/5106}
	   Page 3.00 sharing violation

There is another Waveterm currently using page3.00
Only one waveterm on a network is allowed to use
page 3.00 at any one time. This is due to temporary
files set up while editing transient sounds.



{0120/3504}
	Not a RIFF file

The file you have tried to load is
not a MicroSoft Windows'.WAV' file.

{0121/3504}
	Not a WAVE file

The file you have tried to load is
not a MicroSoft Windows'.WAV' file.

{0122/4804}
	Missing format specification

The MicroSoft Windows '.WAV' file you have
tried to load doesn't contain format infomation.

{0123/4505}
	Cann't find data area

Couldn't find the header for the data area
in the MicroSoft Windows '.WAV' file you have
tried to load.


{0150/2704}
      DOS Write Error.

Unable to open ~
for read/write access.


{0151/2704}
      DOS Read Error.

Unable to open ~
for read access.

{0152/3103}
	DOS File Error

Not Enough data in ~


{0153/3005}
Unable to delete ~

If you are using a network,
another computer may also have
this file open.


{0154/4302}
Unable to rename a file to ~
There may already be a file with this name.



{nnnn/nnnn}
-----------------------------------------------------------------------

{0170/3706}
	File Conversion Error

The file you have tried to load has a
resolution of 12-BITS. The PPG system
will only convert and use files of
8-BIT and 16-BIT.



{nnnn/nnnn}
-----------------------------------------------------------------------
		HELP SCREEN ERRORS
-----------------------------------------------------------------------
{0198/3903}
      Memory Allocation error.

Not enough heap space in save_screen().


{0199/2601}
Unable to find 'HELP.TXT'.

{nnnn/nnnn}
-----------------------------------------------------------------------
		TEMPORARY ERROR MESSAGES FOR PAGE 3.00 TRANSFERS
-----------------------------------------------------------------------
{0300/0901}
error 300

{0301/0901}
Error 301

{0302/0901}
Error 302

{0303/0901}
Error 303

{0304/0901}
Error 304

{0305/0901}
Error 305


{nnnn/nnnn}
-----------------------------------------------------------------------
		WARNING MESSAGES
-----------------------------------------------------------------------
{1000/4505}
	   Bad communications bus.

There have been a number of check sum errors
which could be due to cables being too long
or not correctly screened.

{1001/5505}
            No Math Coprocessor found.

It is recommended that a Math Coprocessor should
be fitted to this machine before running this software
as many complex calculations will slow the machine down

{1002/5206}
               No Math Coprocessor.

This section involves many mathematical calculations
which would greatly slow down the machine.

	  Carry on (y/n)?

{1003/6107}
                No PPG comms card detected.

Without a PPG communications card installed in your computer
there can be no link to any PPG components.

If a card is fitted, please check the address settings on
the DIP switch pack on the board. The address should be 300h.


{1100/2203}
 Directory not empty.

Erase all files (y/n)?


{1101/2103}
File already exists.

Overwrite file (y/n)?


{2000/1101}
Press a key

{2001/5103}
The file you have loaded is a STEREO compound file.
You may have to change the keyboard mode to 1 by
pressing KEYB followed by '1' on the WAVE2.3.


{2002/4702}
This function will clear all data on this page.
Are you sure you want to do this (y/n)?

{2003/2301}
Is this sound ok (y/n)?



{nnnn/0000} - will not show on the system)

			ERROR.TXT file
			--------------

This file contains all the error messages used in the system.
The software will search for the required page by looking for a 4 digit decimal
number following a '{' sign.

Once the software has found the pagenumber it will get the numbers from the
brackets following. The 1st 2 decimal bytes are the maximum length of the lines
to be printed, while the next 2 bytes are the number of lines.

Providing there is enough memory in the computer, it will print up the error
message between the brackets up to the next bracket.


WARNING MESSAGES are called in the same way but are given an error code of
>= 1000.

